Safety in the production of furniture shops (1987)

Collage of frames with furniture production intruments.

Workers come out of the entrance of the Moscow Furniture Assembly Plant No. 1.

Buildings of the combine.

Loading of finished furniture into a special transport.

Furniture sets of the Moscow combine.

Workshop for processing furniture boards.

Safety classes.

The greatest danger is represented by moving and rotating parts of all lines.

Submission of the chipboard plate for processing.

Transformer box.

Ambulance.

Many lines in furniture production are harmful due to their monotonous effect on the nervous system.

The impact of increased noise levels in production.

Transfer of cut panel parts by a manipulator with pneumatic grips.

Ungraded cutting tools are dangerous in different areas.

It is dangerous to touch the working surface of the sanding belt, especially when working.

Fencing of moving parts.

Ventilation equipment on the grinding and finishing line.

Explosion and fire on such a line, in case of exceeding the concentration of dust and gas.

The danger is the touch of hot plates of the press, especially the closing ones.

A great danger is the pneumatic grips and pneumatic springs on the grinding and polishing line.

Continuation of the safety lesson.

Processing line of bar parts.

Be sure to wear headphones and work gloves.

Limiter of the limiting section of materials.

The cutting mechanism and the feeding mechanism must be blocked so that stopping either of them would cause the other to stop.

The method of fastening the knives should completely exclude their departure.

The clamping housings are also interlocked with cutting and feeding mechanisms.

Feeding mechanisms should be covered with casings and flaps that exclude the capture of workers' hands and clothes.

The safe and trouble-free operation of the calibration line largely depends on the thoroughness of its preparation for operation.

The sanding belt should be installed without creases and protruding edges.

The feed rollers should not have surface defects and distortions during feeding.

The design of modern lines provides for remote control, but at the same time, fences, control measuring devices, devices for removing static electricity must be in full working order.

Pneumatic transport systems must be regularly cleaned of blockages for normal operation.

Grounding device.

The cladding line is equipped with a complex of protective devices.

The locking of the caching unit should prevent it from getting into the clamping rollers.

Such a device allows you to instantly stop the gluing rollers in case of danger.

Glue supply to the rollers on the press.

Applying glue to chipboard plates.

Recommendations for washing rollers from glue.

Washing of rollers.

Fencing of machine assemblies for the production of cabinet furniture.

Cutting edges with static knives.

The output of the plates from the press and laying them on a pack of ready-made plates.

The line of format cutting of plates.

The most dangerous line is moving a stack of sheets.

The operator controls the opening.

The fences of the extreme saws are interlocked with the start.

The feeding mechanism is interlocked with the cutting mechanism.

Special devices are used to remove scraps.

Clippings are recycled when they are removed from the line.

The cut parts are transferred by pneumatic grabs to the conveyors.

Fencing of the cutting line of parts.

When moving the plates along the line, limiters must be installed.

The probability of an accident in the absence of limiters is shown.

Edge lining line.

If the loading or unloading devices are not working, the operation of the line is not allowed.

The feeding device must be switched off automatically if the product is not properly fixed in the working position.

Finishing line.

Emergency shutdown device of the putty installation.

Grinding line.

Fencing of rotating parts of mechanisms.

The dust collection system must be blocked by a trigger device.

Varnish-containing containers must be sealed.

Ventilation should always work properly and effectively remove harmful fumes.

At the exit of varnished and polished shields, there should be devices for removing static electricity.

The tool must be made of materials that exclude sparking.

Drilling line, additives and installation of shkantov.

These lines are located with furniture assembly shops.

When setting up the equipment, it is necessary to pay attention to the reliable fastening of cutting tools.

Furniture assembly.

On the assembly line, emergency stop conveyor buttons must be installed at each workplace.

Tools used in the manual assembly of furniture.

The tool must be carefully prepared for use.

Transportation of finished furniture on a loader.

Possible accident during such an operation.

Lesson about safety with the workers of the enterprise.

Personal protective equipment.

Obtaining certificates of verification of safety knowledge.